Hi everyone. Before anything else, I would like to mention that I do not plan to expose absolutely anything to the internet other than using a VPN, and that’s if necessary.

Now, if I understand it correctly, ZigBee compatible devices need a controller attached to the computer to decipher messages? Since we are talking about security, it seems that the ZigBee network has its own encryption technology.

Coming to WiFi which was my original plan, we have established protocols like WPA2. I had intended for all of my IoT devices to be locked in a separate VLAN with no external access.

Which one of them do you think is better for privacy and longevity? I am going to use the basics such as lights, temperature/motion sensors (would like to flash with custom firmware like Tasmota if possible) - alongside some custom devices, which would also be programmed from scratch (ESP32 based). The problem I have with the devices from the latter proposition is that I have to keep on top of security trends myself, but I suppose that’s the trade-off one makes with custom devices.

Please tell me what you use at home and why, between Zigbee and WiFi?

Thanks

    • Ananace@lemmy.ananace.dev
      link
      fedilink
      English
      arrow-up
      6
      ·
      1 year ago

      Lots of people instantly think of security when they look at WiFi-connected IoT devices, but oftentimes they never think of the WiFi signal itself - what with all the added communication noise and send time limitations of having lots of small devices.
      Especially with regular consumer equipment, it doesn’t actually require that many devices to fully saturate a regular home router or AP.

      • Scrath@feddit.de
        link
        fedilink
        English
        arrow-up
        4
        ·
        1 year ago

        That’s a good point. Another one I have is sort of failure tolerance. I used to have a really unreliable router which would often crash and could only be reset using a full power reset. While it was in this state, wifi obviously stopped working but my zigbee devices where still available. I used to have a zigbee button linked to a smart plug for toggling my router off and on again.

        This shouldn’t be a concern for most people obviously but I wanted to share my experience.

        Another point I want to mention is that zigbee works at 2.4Ghz just like basic wifi so they can still interfere with each other.

        Zwave on the other hand uses another frequency (I think it was around 860MHz) but is more expensive.

        • MigratingtoLemmy@lemmy.worldOP
          link
          fedilink
          English
          arrow-up
          1
          ·
          edit-2
          1 year ago

          Do you think I’ll be able to use 915Mhz (I’m in the US) for ZigBee devices using the Sonoff controller and IKEA devices/custom devices? Or is it reserved for specific purposes?

          • Scrath@feddit.de
            link
            fedilink
            English
            arrow-up
            2
            ·
            1 year ago

            Isn’t Zigbee always on 2.4GHz regardless of country? Trying to shift the frequency to 915MHz for all devices sounds like a lot of work with questionable benefit

              • Scrath@feddit.de
                link
                fedilink
                English
                arrow-up
                2
                ·
                1 year ago

                Well, theoretically yes but it doesn’t continuously send data and both WiFi and Zigbee also allow for operation on various channels. Does your neighbors WiFi interfere with yours?

                Also, most WiFi devices now support 5GHz WiFi anyway so it’s even less of an issue anymore. The bigger problem would probably be WiFi interfering with ZigBee. But again, that can be resolved by changing the channels.

      • vzq@lemmy.blahaj.zone
        link
        fedilink
        English
        arrow-up
        3
        ·
        1 year ago

        Especially with regular consumer equipment, it doesn’t actually require that many devices to fully saturate a regular home router or AP.

        Absolutely! If you have devices that still only support b/g, they are going to eat up your air time really quick.

    • MigratingtoLemmy@lemmy.worldOP
      link
      fedilink
      English
      arrow-up
      1
      ·
      edit-2
      1 year ago

      My apologies, I needed to read up on the encryption that ZigBee uses a bit more. I have confidence that anyone snooping on the RF emanating from my flat will very likely not be able to decrypt ZigBee traffic (for that network will likely contain sensitive information). Some of my devices will likely transmit close to all the time (humidity sensor for a plant, for example), I’m hoping such traffic can mask the other more sensitive traffic, like of infrared sensors set up to react to opening the door, as an example.

      Can I use ZigBee at another frequency than 2.4Ghz? I noticed that the US has another operational frequency for ZigBee but I don’t see it discussed very often